Side-Power SP 125 T Manual de Instalação descarregar pdf (Página 10)

Stern tunnel installation version 1.7.2 - 2015

ELECTRICAL INSTALLATION OF STERNTHRUSTER SYSTEMS

To use the Sidepower dual joystick panel with previously installed Sidepower

bowthruster with the older 3 lead electric system.

- Please contact your distributor / dealer to purchase an upgrade kit to rebuild your existing bow-

thruster to the new 4 lead electric system. The wiring diagram on the previous page will then be the

correct one for your complete system.

To use the Sidepower dual joystick panel with previously installed thruster of

other brand.

- You should not use the Sidepower dual joystick panel as it is not designed to run other thruster

brands. It may be possible but you must consult a skilled electrician to ensure the compatibility.

The panel can supply a maximum of 1Amp. in the standard configuaration and will therefore nor-

mally not be able to directly drive main solenoids on a thruster.

- If you wish to use this panel to control another brand of bowthruster, a possible solution is to

rebuild the dual joystick panel, so that it for all practical purposes is transformed into two different

controls.

This is done by removing all connections on the “bow-joystick” including the Sidepower connec-

tor and the yellow cables between the two joysticks.

You must then connect the black lead coming out of the ON/OFF system in the panel to a

seperate ground/negative with the same ground potential the thrsuter because there are no

ground coming from the sternthruster.

By this, the “bow-joystick” is totally seperated from the Sidepower panel and can be used and

connected as any other joystick or two way switch. Consult your other brand thruster manual

for correct connections. We advice to always fit an ON/OFF switch on the input lead to the

joystick so that it’s function can be de-activated when the thruster is not in use. See example

diagram below.

NB! Sleipner Motor claims no compatibility with other thruster brands and assumes no

responsibility for connection or usage with other thruster brands.

Stern thruster installation manual Version 1.6 - 2005

SLEIPNER

SIDEPOWER

THRUSTERS

OFFON ON

BOW

STERN

To Sidepower

sternthruster

To other brand

bowthruster

Visual connection diagram for rebuilt dual joystick panel

Control power

ON / OFF

RH / LH run

LH / RH run

Remove the yellow jumper between BOW and STERN joysticks at the back of the panel.

Move the two grey leads from the BOW joystick to the STERN joystick (a total of four grey leads at STERN joystick)

FUSE

Move the two blue leads from the BOW joystick to the STERN joystick (a total of four blue leads at STERN joystick)

Contact marked with STERN is NOT in use!

Remote installation of Stern thruster systems

To use the Side-Power dual joystick panel with previously installed Side-Power bowthrust-

er with the older 3 lead electric system.

• Please contact your distributor / dealer to purchase an upgrade kit to rebuild your existing bow-thruster to the

new 4 lead electric system. The wiring diagram on the previous page will then be the correct one for your com-

plete system.

To use the Side-Power dual joystick panel with previously installed thruster of other brand.

• You should not use the Side-Power dual joystick panel as it is not designed to run other thruster brands. It

may be possible but you must consult a skilled electrician to ensure the compatibility. The panel can supply a

maximumof1Amp.inthestandardconguarationandwillthereforenormallynotbeabletodirectlydrivemain

solenoids on a thruster.

• If you wish to use this panel to control another brand of bowthruster, a possible solution is to rebuild the dual

joystick panel, so it for all practical purposes is transformed into two different controls. This is done by removing

all connections on the “bow-joystick” including the Side-Power connector and the yellow cables between the

two joysticks. You must then connect the black lead coming out of the ON/OFF system in the panel to a seper-

ate ground/negative with the same ground potential the thrsuter because there are no ground coming from

the sternthruster. By this, the “bow-joystick” is totally seperated from the Side-Power panel and can be used and

connectedasanyotherjoystickortwowayswitch.Consultyourotherbrandthrustermanualforcorrectconnec-

tions.WeadvicetoalwaystanON/OFFswitchontheinputleadtothejoysticksoit’sfunctioncanbedeacti-

vated when the thruster is not in use. See example diagram below.

Visual connection diagram for rebuilt dual joystick panel control

NB! Sleipner Motor claims no compatibility with other thruster brands and assumes no

responsibility for connection or usage with other thruster brands.

1 2 ... 5 6 7 8 9 10 11 12

Comentários a estes Manuais

Sem comentários

Side-Power SP 125 T Manual de Instalação Página 10

Comentários a estes Manuais

Manuais e produtos relacionados com não Side-Power SP 125 T